A drawing specifies an M6 threaded hole with a thread depth of 10 mm. The supplier machines the part, checks the thread with a gauge, and delivers the components.
During assembly, however, the screw either bottoms out before clamping the mating part or cannot achieve the required thread engagement.
This is a common design and manufacturing misunderstanding: the required thread depth and the required drill depth are not necessarily the same.
For CNC-machined components, particularly those with blind tapped holes, the difference affects machining feasibility, tool selection, assembly reliability, and production cost.
Understanding these details before releasing a drawing can help engineers and purchasing managers avoid unnecessary manufacturing problems.
A blind tapped hole is a threaded hole that terminates inside a component rather than passing completely through it.
It is commonly used in:
Aluminum CNC-machined housings
Stainless steel mounting blocks
Precision brackets
Machinery components
Valve bodies and manifolds
Electronic equipment enclosures
Unlike a through-hole, a blind hole has a physical bottom.
This creates additional manufacturing considerations because the cutting tool must stop before reaching the bottom, while sufficient usable thread length must still be produced.
A typical blind tapped hole involves four distinct geometric regions:
Entry chamfer or countersink
Full-form internal threads
Incomplete threads near the tap lead
Drill-point geometry and bottom clearance
These regions should not be treated as one dimension.
This is the most important distinction when designing blind tapped holes.
Full thread depth is the usable length of complete internal threads available for screw engagement.
It is the portion of the hole intended to provide the specified threaded connection.
The required depth depends on factors such as:
Fastener diameter and pitch
Base material strength
Fastener material
Applied load
Thread engagement requirements
Assembly and service conditions
A cutting tap does not produce complete threads from its very first cutting edge.
The leading portion of the tap has a chamfer, also called a lead. Its cutting teeth progressively form the thread profile.
Consequently, the tap must travel farther than the required full-form thread depth.
The amount depends on the selected tap geometry.
The drilled hole must generally be deeper still.
Additional depth may be needed to accommodate:
Tap lead
Chip accumulation
Tool clearance
Drill-point geometry
Machine positioning and process variation
A drill also normally creates a conical bottom unless a different bottom geometry is specifically machined.
The key principle: A drawing that requires 10 mm of usable full-form thread should not automatically specify a 10 mm drill depth.
There are three main reasons.
A cutting tap has a tapered leading section.
The first few cutting teeth progressively develop the thread rather than producing the full thread profile immediately.
Different tap designs have different lead lengths.
For example:
Taper taps have relatively long leads.
Plug taps have shorter leads.
Bottoming taps are designed with shorter leads for applications requiring threads closer to the bottom.
However, even a bottoming tap does not produce complete threads all the way to the physical bottom of a blind hole.
The appropriate tap depends on the material, hole depth, thread size, and chip evacuation requirements.
A conventional twist drill produces a conical point at the end of a blind hole.
The full-diameter cylindrical portion of the hole therefore ends before the deepest point reached by the drill.
This matters when calculating usable space for a tap or screw.
The drill-point geometry should be considered separately from the required full-thread depth.
During tapping, material is removed from the hole.
In a blind hole, chips must be managed without obstructing the tool.
If the hole has insufficient clearance, chips can accumulate near the bottom and increase cutting resistance.
Potential consequences include:
Tap breakage
Damaged threads
Incomplete thread formation
Poor surface quality
Production downtime
Chip evacuation becomes particularly important when machining materials that produce difficult-to-manage chips.
The tap geometry and cutting strategy should therefore be selected together with the hole design.
Not all taps are designed for the same conditions.
| Tap Type | General Characteristics | Typical Consideration |
|---|---|---|
| Taper tap | Long leading chamfer | Thread starting and easier entry |
| Plug tap | Intermediate leading chamfer | General-purpose threading |
| Bottoming tap | Short leading chamfer | Producing usable threads closer to the hole bottom |
| Spiral flute tap | Designed to lift chips out of blind holes | Chip evacuation |
| Forming tap | Forms threads by material displacement | Requires suitable material and pre-hole size |
The table describes general characteristics. Actual lead geometry, recommended application, and operating conditions vary by tap manufacturer and tool design.
For example, a spiral-flute tap may be suitable for certain blind-hole applications because it helps evacuate chips toward the opening.
A forming tap may eliminate cutting chips, but it requires an appropriate ductile material and correctly sized pre-drilled hole.
The supplier should select the tool based on the actual part requirements rather than relying on one universal tapping method.
Consider a hypothetical aluminum mounting block with the following drawing requirement:
Thread: M6 × 1
Required full thread depth: 10 mm
Screw engagement: 10 mm nominal
Hole type: Blind
The designer specifies the thread size and required usable thread length.
However, the manufacturing engineer must also determine:
Which tap design will be used?
How long is its chamfer?
What drilling depth is required?
How much space is needed for chips and tool clearance?
What is the drill-point geometry?
Could the mating screw contact the bottom of the hole?
The total drilled depth must be determined from these factors.
It would be incorrect to assume that the drill depth should simply equal 10 mm.
It would also be incorrect to apply one universal extra-depth allowance without considering the selected tool and process.
This is why the drawing should clearly distinguish the required full-thread depth from the overall hole depth.
A screw that is longer than the available usable hole depth can bottom out.
This can create a misleading assembly condition.
The operator may feel that the screw has tightened, even though the clamping faces have not fully contacted each other.
Possible consequences include:
Inadequate clamping force
Incorrect assembly positioning
Damaged internal threads
Screw loosening during service
Inconsistent assembly torque
This problem is particularly important for aluminum housings and precision mounting components.
A screw should not be allowed to bottom out unintentionally when the joint is designed to generate clamping force between two mating surfaces.
For critical assemblies, the screw length, washer thickness, mating-part thickness, thread engagement, and hole geometry should all be reviewed together.
Where component functionality permits, a through-hole can simplify manufacturing.
| Factor | Blind Tapped Hole | Through Tapped Hole |
|---|---|---|
| Access | One side | Through the component |
| Drilling | Requires bottom-depth planning | Easier depth management |
| Chip evacuation | More demanding | Generally easier |
| Tool travel | Limited by hole bottom | More available travel |
| Design flexibility | Useful where the opposite side must remain closed | Requires an opening on both sides |
| Manufacturing risk | Greater sensitivity to depth and chip management | Often simpler tapping conditions |
A blind hole is necessary when the opposite surface must remain intact, when the component has a closed housing, or when the design requires a threaded feature without breakthrough.
However, if a through-hole does not compromise the component's function, it may be worth discussing with the manufacturer during DFM review.
The final decision should consider assembly, sealing, appearance, structural requirements, and manufacturing cost.
A good engineering drawing should communicate what the screw connection actually requires.
For a blind tapped hole, consider specifying:
Thread designation
Thread pitch
Thread tolerance class where applicable
Minimum full-form thread depth
Overall drilled-hole depth where critical
Hole entry chamfer, if required
Material specification
Special inspection requirements
For example, an illustrative metric callout might identify an M6 × 1 internal thread, a specified tolerance class, and a minimum usable thread depth of 10 mm.
The drawing should separately define the drill depth when that dimension is functionally or manufacturing-critical.
For Unified inch threads, the applicable ASME B1.1-2024 standard addresses thread forms, series, classes, allowances, and tolerances.
For ISO metric general-purpose threads, ISO 965-1:2026 addresses the tolerance system and basic data.
These standards define thread-related requirements; they do not replace the need to specify application-specific blind-hole depth and screw clearance.
Technical references:
Thread inspection should confirm more than the nominal thread size.
Depending on the drawing and application, inspection may include:
Go/no-go thread gauges can be used to verify thread acceptability according to the applicable gauging requirements.
However, a thread gauge passing does not automatically prove that the hole has the required usable thread depth.
A suitable depth-measuring method can verify whether sufficient thread engagement is available.
The measurement method should distinguish the usable full-form thread region from incomplete threads and the hole bottom.
For some assemblies, a functional screw engagement check may help verify that the fastener reaches the intended position without bottoming out.
This should not replace specified dimensional or thread-gauge inspection where those are contractually required.
Where screw bottoming is a functional risk, the drawing and inspection plan should define how the available clearance is verified.
The required documentation should be agreed upon before production.
Mistake 1: Specifying thread depth equal to drill depth
This ignores the tap lead and drill-point geometry.
Mistake 2: Assuming all taps produce the same thread depth
Different tap designs have different leading geometries and process requirements.
Mistake 3: Ignoring chip evacuation
A blind hole can become difficult to tap if chips accumulate at the bottom.
Mistake 4: Selecting screw length without checking available hole depth
The screw may bottom out before the mating surfaces are clamped.
Mistake 5: Using an unnecessarily deep blind hole
Excessive depth can increase machining time, material removal, and tooling requirements without improving functionality.
Mistake 6: Failing to identify the inspection requirement
Thread size, usable thread depth, and screw bottom clearance are separate characteristics.
When requesting a quotation, provide the following:
| Item | Information |
|---|---|
| Part drawing | Current revision |
| Material | Grade and condition |
| Thread designation | Metric or Unified inch |
| Thread pitch | Clearly specified |
| Thread tolerance | Applicable class or standard |
| Full thread depth | Required usable thread length |
| Drill depth | When specified or functionally necessary |
| Hole type | Blind or through |
| Fastener | Screw size and intended engagement |
| Surface treatment | Coating or finishing requirements |
| Inspection | Thread gauge and depth verification |
| Quantity | Prototype and production demand |
If the drawing contains blind tapped holes with limited bottom clearance, ask the supplier to review manufacturability before releasing the order.
This is especially important for components involving multiple tapped holes, deep cavities, or difficult-to-machine materials.
Blind tapped holes require more than a thread diameter and nominal depth.
The usable full-thread length, tap lead, drill-point geometry, chip clearance, and screw engagement all influence whether the finished component will work as intended.
For engineers and purchasing managers, clearly distinguishing thread depth from drill depth helps reduce machining errors, prevent screw bottoming, and avoid unnecessary production costs.
For related CNC manufacturing applications, explore CPRMFG's Swiss Machining Stainless Steel Parts and precision manufacturing services.
Need a quotation for custom CNC machined parts? Contact CPRMFG with your engineering drawings, material grade, thread specifications, required quantities, and inspection requirements. Our team can review the drawing and discuss a suitable manufacturing quotation.
Thread depth refers to the usable full-form threaded length. Drill depth refers to how deep the drilled hole extends. The drill depth generally needs to accommodate the tap lead and additional clearance.
No. A bottoming tap has a shorter lead, but it still cannot produce complete threads down to the physical bottom of a conventional blind hole.
Clearance accommodates the tap lead, drill-point geometry, chips, and tool travel. The exact requirement depends on the selected tooling and machining process.
Yes. A thread gauge checks thread acceptability, not necessarily the relationship between usable hole depth and screw length. Separate depth and assembly checks may be necessary.
Generally, yes. They often provide better chip evacuation and eliminate the need to manage a closed hole bottom. However, the design must permit an opening on the opposite side.
Provide the thread designation, pitch, tolerance class, required full-thread depth, material, hole type, quantity, and any specific inspection requirements.